‹ Go back
1929 Ford Model A Pickup & Model A Parts - Online Only Auction
Location:
Address:
When:
Auction Organizer:
Web Site:
Wellington, KS 67152
1101 E. 16th Street
Dec 1, 2025 - Dec 29, 2025. Lots begin to close on Monday, December 29th @ 1:00 PM
Theurer Auction/Realty LLC
Public Auction Information
1929 Ford Model A, Completely Restored and Runs; and Model A Parts - Online Only Auction
When: Monday, Dec 29th at 1:00 PM
Where: 1101 E 16th Street, Wellington, KS
Vehicle Info - 1929 Ford Model A Pickup, VIN #G3673, Runs and Drives
History from the Owner, Marvin "Leon" Stovall:
Purchased in 1955 for $200
Motor overhaul after 1973
Current engine from old Gleaner Combine
New canvas top and reupholstered the seat
2019 decided to "Hot Rod" it up - all changes can be reverted back to Ford factory
Neither frame nor body have been cut
October 2019: Converted to 12 Volt Negative Ground and FSI Ignition (J.D. Hanks in Oklahoma City)
New "Leakless Water Pump", new terminal box, new floor mat, grommets and distributor parts
New wiring kit, tail light bracket, speedometer cable oval and safety fuse; new tail light, brake pedal return spring, clevis pins; wire connectors for tail light parts to overhaul the original tail light
"LOGO" Lites signal kit for turn signal
New manifold heater but hadn't ever used it
Bought 2006 Chevrolet Equinox electric steering unit from Lumbert's Salvage Yard in Winfield KS
Overhauled brakes -- new brake linings on parking brake; replaced worn brake control rods and pins; front and rear brake assemblies overhauled by Snyder's Antique Auto
Did NOT replace bushings on the parking brake cross shaft or the service brake cross shaft
Overhauled steering column - no balls left in the bearings and was still hard to steer after the overhaul so chopped it up and mounted the electric power steering unit
January 2020: Overhauled speedometer and speedometer cable and the end that goes to the transmission
Spring 2020: Clutch housing rebuilt by Snyder's and light weight flywheel and V8 clutch balanced; new heavy duty radiator (original radiator had 6 cooling fins per inch ... the new one has 8)
Sept 15, 2020: New white sidewall tires mounted
Engine overhauled by Eric at Model A Medic in Wichita KS; smoothest engine - starts right up and idles smoothly -- 6:1 compression head, insert bearing and Stromberg 97 carb and manifold (Engine build sheet in Documents along with additional instructions and mapping guides).
For more information click on the image above or go to https://www.theurer.net/. For questions call (620) 326-7315 or email info@theurer.net
When: Monday, Dec 29th at 1:00 PM
Where: 1101 E 16th Street, Wellington, KS
Vehicle Info - 1929 Ford Model A Pickup, VIN #G3673, Runs and Drives
History from the Owner, Marvin "Leon" Stovall:
Purchased in 1955 for $200
Motor overhaul after 1973
Current engine from old Gleaner Combine
New canvas top and reupholstered the seat
2019 decided to "Hot Rod" it up - all changes can be reverted back to Ford factory
Neither frame nor body have been cut
October 2019: Converted to 12 Volt Negative Ground and FSI Ignition (J.D. Hanks in Oklahoma City)
New "Leakless Water Pump", new terminal box, new floor mat, grommets and distributor parts
New wiring kit, tail light bracket, speedometer cable oval and safety fuse; new tail light, brake pedal return spring, clevis pins; wire connectors for tail light parts to overhaul the original tail light
"LOGO" Lites signal kit for turn signal
New manifold heater but hadn't ever used it
Bought 2006 Chevrolet Equinox electric steering unit from Lumbert's Salvage Yard in Winfield KS
Overhauled brakes -- new brake linings on parking brake; replaced worn brake control rods and pins; front and rear brake assemblies overhauled by Snyder's Antique Auto
Did NOT replace bushings on the parking brake cross shaft or the service brake cross shaft
Overhauled steering column - no balls left in the bearings and was still hard to steer after the overhaul so chopped it up and mounted the electric power steering unit
January 2020: Overhauled speedometer and speedometer cable and the end that goes to the transmission
Spring 2020: Clutch housing rebuilt by Snyder's and light weight flywheel and V8 clutch balanced; new heavy duty radiator (original radiator had 6 cooling fins per inch ... the new one has 8)
Sept 15, 2020: New white sidewall tires mounted
Engine overhauled by Eric at Model A Medic in Wichita KS; smoothest engine - starts right up and idles smoothly -- 6:1 compression head, insert bearing and Stromberg 97 carb and manifold (Engine build sheet in Documents along with additional instructions and mapping guides).
For more information click on the image above or go to https://www.theurer.net/. For questions call (620) 326-7315 or email info@theurer.net
